Simple Repair Technology of Aged EPDM Ground Using Colored Elastic Adhesive
You are here: Home » Blogs » EPDM » Simple Repair Technology of Aged EPDM Ground Using Colored Elastic Adhesive

Simple Repair Technology of Aged EPDM Ground Using Colored Elastic Adhesive

Views: 0     Author: Site Editor     Publish Time: 2026-06-10      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
sharethis sharing button

1. Introduction

EPDM elastic ground is widely used in outdoor activity venues due to its safety, elasticity and anti-slip performance. After long-term ultraviolet aging, rain erosion and frequent trampling, most EPDM grounds appear superficial damage, including color fading, particle loosening, surface voids and slight sanding. In most cases, the base layer is still stable and does not need overall reconstruction. The colored elastic adhesive repair technology targets such superficial defects. Through one-time cleaning, local patching and overall gluing, it reinforces the old surface and restores uniform color, which is a cost-effective and efficient maintenance solution for aged EPDM grounds.

2. Applicable Damage Conditions

Colored adhesive repair applies to EPDM grounds with stable base structure, mainly for the following minor and moderate damages:

(1) Surface fading and mottled color difference caused by solar aging;

(2) Loose particles and sporadic particle falling without large-area peeling;

(3) Worn and rough surface with tiny voids and dust accumulation;

(4) Local shallow wear and bare glue on partial pavement.

This method is not suitable for venues with severe base hollowing, large-area cracking and delamination failure.

3. Advantages of Colored Adhesive Repair

Compared with traditional particle resurfacing, colored adhesive repair has prominent practical advantages.

Low cost and high efficiency. There is no need to remove the original effective particles, which saves material and construction costs. The whole process is simple and the construction period is short.

Integrated color restoration. Custom color matching ensures no obvious color difference between the repaired area and the original ground, solving the mottled appearance of local patching.

Structural reinforcement. The elastic adhesive penetrates into particle gaps, rebinds loose particles and seals surface voids, improving the overall compactness and wear resistance.

Safe and environmentally friendly. The polyurethane colored adhesive is non-toxic and weather-resistant. After curing, it retains the original elasticity and anti-slip performance of EPDM ground.

4. Standard Simple Construction Process

The repair process is concise and practical, suitable for on-site rapid construction.

Step 1: Full surface cleaning. Remove dust, dirt, moss and completely loose particles. Clean particle gaps thoroughly and keep the surface dry and clean to ensure bonding quality.

Step 2: Local defect patching. For worn bare areas and shallow pits, fill and level with mixed colored adhesive and fine EPDM particles to eliminate uneven surfaces.

Step 3: Color matching and glue mixing. Match the adhesive color according to the original venue tone. Mix adhesive and curing agent evenly in standard proportion to avoid bubbles and precipitation.

Step 4: Overall roller coating. Coat the colored adhesive evenly on the whole ground. The adhesive penetrates and bonds loose particles, forming a dense and uniform color protective layer. A second coating can be applied for severely faded surfaces.

Step 5: Finishing and curing. Trim edges and detailed positions to ensure flat transition. Seal the site for curing for 24–48 hours at room temperature until fully hardened.

5. Daily Maintenance After Repair

After construction, avoid heavy rolling and sharp scratching within one week. In daily use, clean the ground regularly with neutral detergent, and avoid strong acid and alkali corrosive agents. Regular inspection is recommended. Timely supplementary gluing for minor wear can effectively prolong the service life of EPDM ground. It is suggested to carry out one colored adhesive reinforcement coating every 2–3 years for outdoor venues.

6. Conclusion

Colored elastic adhesive repair is a simple, economical and efficient renovation method for aged EPDM grounds. It avoids resource waste caused by overall reconstruction, effectively solves common superficial aging problems, and integrates structural reinforcement and color beautification. With simple process, low cost and reliable performance, this technology is very suitable for daily maintenance and minor renovation of various EPDM activity venues, and can well maintain the safe and beautiful use state of elastic pavement.

CNMI Industrial Corp is an industry leader in epoxy resin and pigment manufacturing.
We have been serving the Resin art DIY,Epoxy floor,Carbon &fiber compisite.

Quick Links

Products

Policy

Contact us
 Copyright © 2024 CNMI Industrial Corporation. All rights reserved. Sitemap Support by leadong.com Privacy Policy